FMUSER 150W FM transmitter with 1/2 wave dipole antenna and 20 meters cable

FMUSER 150W FM transmitter with 1/2 wave dipole antenna and 20 meters cable





Images displayed are taken by FMT-80A(80W), The only difference is the amplifier board.
Check our FME-150A Kit for amplifier board details by item No. 290555149041

Updated on FMT-30A (1U), the latest version (Ver2.1)
Power adjustable: 0-150 watts.
LCD displays working frequency, volume, temperature, forward power, reflected power and SWR,
Single knob operation.
Automatic power control maintaining the output at any preset level
Pre-emphasis optional at 0, 50us or 75us.
Dual stereo audio input interface.
Provided with SWR protection function and temperature protection, raise alarm prompts once meet any trouble while working.
Standard 19 inches, 2U whole aluminum case.
Wiredrawing and oxidation makes surface bright, clean and elegant.

Power supply voltage: 110V or 220V (can be switched)
Power Output: 0 to 150Watt adjustable (step 1W)
Frequency range: 87.5-108 MHz
Frequency Step: 0.1MHZ
Operating Current: Less than 4A
Harmonic suppression: -65 dBc
Operating temperature: -10 ℃ ~ 50 ℃
Frequency stability: ± 10 ppm (-10  ° C to +60 ° C )
Frequency Response: 50 – 15000Hz
SNR: More than 50dB
Distortion: less than 0.5%
Parasitic amplitude modulation: Less than 0.2%
Frequency deviation: Less than ±75KHz
Modulation Mode: WFM
Transmission Signal: FM Stereo or Mono
Tuning Design: Stable PLL Technology
Audio Input Level: -15db Max: -30db
Stereo Separation: More than 40db
Output Impedance: 50 ohm
Audio Input: RCA
AUX Input: BNC
Antenna Connector: N
Unit Size: 483mm * 400mm * 89mm (2U)
Package weight: 8.5Kg

Dipole antenna:



A dipole antenna is a radio antenna that can be made of aluminum, copper, and bronze tube with a center-fed driven element. It consists of two metal conductors of rod, oriented parallel and collinear with each other (in line with each other), with a small space between them.

The dipole antenna is a particularly important form of RF antenna which is very widely used for radio transmitting and receiving applications. The dipole is often used on its own as an RF antenna, but it also forms the essential element in many other types of RF antenna. As such it is the possibly the most important form of RF antenna.

A half-wave dipole antenna means the length of this dipole antenna is equal to a half-wavelength at the frequency of operation.

Why do we recommend this dipole antenna?

1).The half-wave dipole is very clear and easy for frequency adjustation, there are scales on the side bar of the antenna from which you can adjust the frequency from 88~108 by 1 MHz stepping. 2).The dipole is a simple antenna to construct and use, and many of the calculations are quite straightforward.
3.) The radiation pattern and high gain of dipole:
Radiation pattern of a half-wave dipole antenna, scale is linear.

The Gain of a half-wave dipole (same as above). The scale is in dBi (decibels over isotropic).

SWR diagram of the half wave dipole at 88 MHz

Attention: When setting the antenna, the “Anode” end should be face up, “negative electrode” should be face down

Electrical specification:

Frequency range: 88~108 MHz (1MHz stepping)
Input Impedance Impedance: 50 ohm
VSWR <1.5
Gain: 3.5 dBi
Polarization: Verticality
Maximum Power Input: 150W
Horizontal 3dB Beam Width: 360 °
Vertical 3dB Beam Width: 73 °

Mechanical Specifications:

Height: 990mm
Radiating Element Material: Aluminum Alloy
Connector: SL16-K
Holding Rod Diameter: Φ30~Φ40 mm



Now widely used in: 2G/3G cell phone coverage hotels, schools, hotels, railway stations, docks, office buildings, factories, residential quarters and other areas with wlan / wifi signal coverage, various wireless intercom system, short wavelength radio waves various ham frequencies are supported!

The cable supports:
The frequency 0-12G
Note: 1/2 what does it mean?
Is the outer diameter of the metallic shield of the feeder units of inches, regardless of the inner core and coaxial .1 / 2 refers to the outer diameter of the metal shield is 1.27 cm feeder 7/8 refers to the feeder outer diameter of the metallic shield is 2.22 cm, the outer insulation is not including.

Depending on the wireless transmission of electromagnetic waves in the frequency in the feeder, the attenuation of the signal intensity is different. For example: the electromagnetic frequency: 890 — 920M, attenuation at 1/2 feeder is: 7.5 – 7 .7dB/100 meters. 7/8 feeder attenuation of approximately: 4.2 – 4 .5/100 meters.

If you need longer cable, please let me know.

Package includes:
1*150W fm transmitter
1*DP-100 dipole antenna
1*20meters cable with connector


Leave a Reply

1 Response

  1. Moses 2017/07/12 at 13:16:01

    I would like to know the price for only 1 piece,and how long it takes to ship to nyc