Buy it Now
1 pcs sample
0-600W radio broadcast station FM transmitter PCB KITS
1、 It applies the most advanced LDMOS transistor MRFE6VP5600H on the new amplifier, makes which posses a higher VSWR that can reaches 65:1. In the same time, it still can resists 28 db gain and 80% efficiency. The good performance has greatly exceed BLF574
2、 The architecture proposal which we raised for FSN-600 is efficient with lower budget by using the PCB material is Teflon. It is composed by LPF and power detector coupler. Meanwhile, the FME-1B interface is compatible. And the installation is more simpler and faster when combined with FME-1B. The reason why we do this is to lower down the threshold of the installation for the 600w transmitter equipment. Even a new member only need no more than half an hour;
3、 Although we did not provide the free service guarantee for the previous production, we change the rule since we sell the production of FSN-301. If you buy any of the two transmitter , you can enjoy the two years free after sale guarantee for LDMOS , and one years for all the hardware. which is never happened before.
– A Kind Reminder: This is a kit and skilled assembly is required.
– The Kit includes an amplifier board, a control panel board, an interface board and connection cables.
– Power adjustable: 0-600 watts
– LCD displays working frequency, volume, temperature, forward power, reflected power and SWR, Single knob operation.
– Automatic power control maintaining the output at any preset level Provided with SWR protection function and temperature protection, raise alarm prompts once meet any trouble while working.
(1) Control panel board
– It includes FM modulation circuit, user interface circuit, RF drive circuit, fan control circuit, auto power control circuit.
– The RF output of this board is 1 watt.
(2) Amplifier board
– The amplifier circuit includes power amplifier circuit, power and SWR measuring circuit, digital temperature detection circuit.
(3) Interface Board
– Dual stereo audio input interface.
– RS232 port (Only for factory Program debug).
– AUX interface(External SCA, RDS modulator input).
– Signal input level preset potentiometer.
(4) Connection cables
– Connect control board with amplifier board cable.
– Connect control board with interface board cable.
– RF cable: connect control board with the final stage amplifying board.
– Fool-proofing designed by color with IDC interface.
– Power supply voltage: DC 50V
– Power Output: 0 to 600Watt adjustable (step 1W) ± 0.2dB
– Frequency range: 87.5-108 MHz
– Frequency Step: 0.1MHZ
– Operating Current: Less than 17A
– Input power: Less than 1 watt
– Harmonic suppression: -65 dBc
– Operating temperature: -10 ℃ ~ 50 ℃
– Frequency stability: ± 10 ppm (-10 ° C to +60 ° C )
– Frequency Response: 50 – 15000Hz
– SNR: More than 50dB
– Distortion: less than 0.5%
– Parasitic amplitude modulation: Less than 0.2%
– Frequency deviation: Less than ±75KHz
– Modulation Mode: WFM
– Transmission Signal: FM Stereo or Mono
– Tuning Design: Stable PLL Technology
– Audio Input Level: -15db Max: -30db
– Stereo Separation: More than 40db
– Output Impedance: 50 ohm
– FME-1B panel Size: 260MM(L) * 30MM(W) * 39MM(T)
– Amplifier PCB Size: 170MM(L) * 70MM(W) * 70MM(T)
– Amplifier board *1
– Control panel board *1
– Interface board *1
– Connection cable *3
600w PCB use the power supply as below: 324USD for free shipping
|SETUP.RISEHOLD.TIME||300ms,50ms /230VAC 300ms,50ms/115VACat full load|
|HOLD TIME(TYP.)||20ms/230vac 15ms/115vac at full load|
|VOLTAGERANGE||90~132VAC/ 180-264VAC selected by junper or switch 248~370VDC|
|AC CURRENT||17.5a/115vac 10a/230vac|
|INRUSH CURRENT||35a/115ac 55a/230vac|
|OVERLOAD||105~125%rated output power|
|Protection typeHiccup mode,recovers automatically after fault condition is removed|
|OVER VOLTAGE||57.6 ~ 67.2V|
|Protection type : Shut down o/p voltage, re-power on to recover|
|OVER TEMPERATURE||70±5TSW1Detect on heatsink of power transistor|
|Protection typeShut odown o/p voltage,re-power on to recover|
|DC_OK SIGNAL||PSU turn on:3.3V ~ 5.6V PUS turn off:0 ~ 1V|
|REMOTE CONTROL||RC+/RC-:0-0.8V power on ;4-10v power off|
|WORKING TEMP||-20~+60 (refer to output load derating curve)|
|WORKINGHUMIDITY||20~90% RH non-condensing|
|STORAGE TEMP HUMIDITY||-40~+85 10~95%RH|
|VIBRATION||10~500HZ,2G10min/1cycle period for 60 min each alongX,Y,Zaxes|